Welcome to the North American Subaru Impreza Owners Club Sunday April 18, 2021
Home Forums Images WikiNASIOC Products Store Modifications Upgrade Garage
NASIOC
Go Back   NASIOC > NASIOC Technical > Normally Aspirated with bolt-on Forced Induction Powertrain

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.







* As an Amazon Associate I earn from qualifying purchases. 
* Registered users of the site do not see these ads. 
Reply
 
Thread Tools Display Modes
Old 08-08-2007, 10:41 PM   #1
SubieStylez
Scooby Specialist
 
Member#: 98709
Join Date: Oct 2005
Chapter/Region: NESIC
Location: Saugus, MA
Vehicle:
2005 Impreza WRX 18g
EWG + Meth

Default EJ18T pistons

I have an EJ18 im rebuilding. I was planning on doing a full turbo kit but still keeping it a daily driver. Heres some of the stuff I had planned, VF43 turbo, STi injectors and fuel rails, STi headers, Crossmember, ERZ Uppipe and a full custom exhaust. I was planning on going with EJ20 or EJ22 heads. As for the internals on the block comes some questions. I wanted to do pistons and rods but didnt know which to go with if any possible. What I mean is, would I have to get custom pistons made for the 1.8l? I see EJ20,257 pistons everywhere but none for the EJ18 (which im not surprised at). For the rods I would go with Scat along with ACL main and rod bearings. I have no clue on rings either for the pistons. I seen people running the turbo leg pistons but their hard to come by.
* Registered users of the site do not see these ads.
SubieStylez is offline   Reply With Quote
Sponsored Links
* Registered users of the site do not see these ads.
Old 08-09-2007, 06:40 AM   #2
jedz123
Scooby Newbie
 
Member#: 67083
Join Date: Jul 2004
Chapter/Region: NESIC
Location: Northfield, VT
Vehicle:
1993 Impreza L HB
EJ25D swap, 5-speed FWD

Default

Your rods and crank are forged no need to replace those. As for dropping you compression throw on some EJ22 heads. There are loads of threads about this, it has been done before. Good setup I was going to build one of my own but decided to do the H6 swap instead. Good luck, good hunting.
~Jedz
jedz123 is offline   Reply With Quote
Old 08-09-2007, 11:52 AM   #3
mxpunk
Scooby Specialist
 
Member#: 132130
Join Date: Nov 2006
Chapter/Region: TXIC
Location: Austin, Texas
Vehicle:
2002 Ford F-150
Graphite Gray

Default

use ej22e or ej22t heads. you can use jdm ej20g/k heads or usdm ej207 heads but you need to swap over the sensors to those manifolds

if you want low-comp forged pistons, they will need to be custom.

i thought about this but you can get a wrx shortblock for cheap and even cheaper with a spun-rod bearing, and you could build it yourself and have a stout motor.

do a searhc, theres plenty of ej18s on here including myself..
mxpunk is offline   Reply With Quote
Old 02-12-2021, 11:19 AM   #4
93ImpIndy
Scooby Newbie
 
Member#: 503122
Join Date: Jun 2019
Default Ej18E Rings

Nowhere have I found any rings for my piston. I pulled my engine apart and the rings were halfway gone. The motor had 250000 and I am turbo charging now. I don't want those rings on there, but everywhere says they are sold out. Does anyone have any ideas. I have the .50mm oversized but they wont even slide in the block.
93ImpIndy is offline   Reply With Quote
Old 02-13-2021, 12:37 AM   #5
SoCoNoHa
Scooby Newbie
 
Member#: 478524
Join Date: Nov 2017
Chapter/Region: NESIC
Location: 1997 2.2LGT GT35
Vehicle:
1995 EZ30 Coupe
Green

Default

I've never been able to find pistons for the 1.8, but I've seen rings for sale on eBay and such. The 1.8 block with 2.2T heads is a wonderful combo if you already have all the parts. The block is arguably tougher than any other N/A engine given the thick cylinder walls and compact pistons.
However, if you can get your hands on an EJ22 shortblock and EJ25/EJ20 heads, you'll be way better off. That motor is the balls, I'll probably never build a different 4cyl unless I get around to a 2.5 destroker. The 22T heads just don't flow like the others, and the extra displacement helps a lot too.
Just my .02.

Oh yea, fuel efficiency would be another win for the 1.8 I think.
SoCoNoHa is online now   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
.010 oversize rings + factory piston... Yay or Nay? Jagular1785 Built Motor Discussion 4 06-06-2010 01:45 AM
CT: WRX Heads 02-05, Forged/Stock pistons JDMLegacyEJ25 Private 'Wanted' Classifieds 4 06-03-2010 03:09 PM
Pics of my EJ18T scoobyimprza Normally Aspirated with bolt-on Forced Induction Powertrain 13 11-01-2003 11:14 PM
Pics of my EJ18T scoobyimprza Subaru Conversions 8 10-02-2003 11:16 PM
finalizing EJ18T fuel system setup scoobyimprza Normally Aspirated with bolt-on Forced Induction Powertrain 2 06-26-2003 07:06 PM

All times are GMT -4. The time now is 04:57 PM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2021 Axivo Inc.
Copyright ©1999 - 2019, North American Subaru Impreza Owners Club, Inc.

As an Amazon Associate I earn from qualifying purchases.